Skip to main content Skip to search Skip to main navigation

Product information "Feeler gauge"

Feeler gauge
for setting the contact breaker and ignition
13 sheets
0.05 - 1mm

Herstellerinformationen:
NSU Quickly und Moped Ersatzteile GmbH & Co.KG Siemensstr. 8 77948 Friesenheim WEEE-Nummer:

Verantwortliche Person:
B. Krippl B. Krippl Siemensstrasse 8 77948 Friesenheim DE info@nsu-quickly.de

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Skip product gallery

Similar products

Average rating of 5 out of 5 stars

Alternator side cover
Note different versions! for all 2-speed and 3-speed models with brake lever on the left-hand side of the motor: Quickly N, S, L, N23 and S23 or version for engines with brake lever on the right: Quickly S2, S23-2, F23, TT, TT/K

From €42.00*
Bearing bolt for breaker, type 1
Breaker bearing bolts for all "Type 1" breakers

€6.80*
Breaker
Complete circuit breaker - note the different versions! Type 1 Bosch No. 1217013010, centre hole 6 mm, adjustment via eccentric,most common versionType 2 centre hole 8 mm, adjustment via 2 notches Please refer to the illustrations

From €9.50*

Average rating of 5 out of 5 stars

Capacitor
Typ: Schraubausführung
Ignition capacitor different versions (for soldering or screwing) Capacitors are a frequent source of faults due to their age and should always be replaced

€4.80*
Clutch nut / pole wheel set with spring washers
Set of nuts for clutch or pole wheel, consisting of 1X nut and 2X spring washer - galvanised

€1.00*
Connection plate for cable (on motor)
Connection plate for light cable at the output of the ignition system

€5.20*
Horn (buzzer) 6 V
6 volt snare, universal with holder - alternating current

€7.90*
Ignition cable 1 m
Ignition cable available in 5 mm or 7 mm diameter.Length per unit: 1 m Manufacturer: 5mm: orig. Bosch7mm: Herth+Buss

From €3.60*
Ignition cable 1.90m roll 5mm
Ignition cable 5mm, especially for ignition coil type 3

Content: 1.9 Meter (€2.05* / 1 Meter)

€3.90*
Ignition coil
Ignition coil suitable for various models, please measure and compare accordingly! Dimensions: Type 1: Overall length 73 mm, hole spacing 53 mm Type 2: Overall length 74 mm, hole spacing 50 mm Type 3: Overall length 77 mm, hole spacing 54 mm Type 4: Replacement is type 1

From €50.00*
Ignition system alternator, new NSU Quickly, black coil
Complete new ignition alternator for NSU Quickly Ready to install without soldering!with black, reinforced ignition coilAdvantages: very strong ignition spark with cable (no soldering) Extremely durable Very low susceptibility to faults Quick to replace Ignition coil in original design with wide pole shoes Light output 17 watts, incl. pole wheel. A comparison is worthwhile!1) incl. original Beru ignition cable with rubber grommet2) Light cable outlet on base plate in original version. Position3) Power ignition coil with wide pole shoes!4) Connection plate for light cable enclosed5) Original thread for pullerSuitable for all models.

€139.00*
Ignition tuner
Easy-to-use ignition tuner Determine top dead centre, set pre-ignition - that's it! Screwed into the spark plug thread.

€36.00*
Skip product gallery

Customers also bought

Ignition tuner
Easy-to-use ignition tuner Determine top dead centre, set pre-ignition - that's it! Screwed into the spark plug thread.

€36.00*
Spark plug "Bosch"
Bosch Multi-range candle, ideal for the Quickly

€4.90*
Puller for pole wheel
Pole wheel puller for all Quickly motors Notes: Please note that the thread of the crankshaft must be protected by a brass pressure piece or similar if the pole wheels are stuck.Alternatively, the nut of the pole wheel can remain on the threaded stub.(loosen nut and turn flush to the end of the thread).

€8.80*

Average rating of 5 out of 5 stars

Hook spanner for exhaust fitting
Suitable hook spanner for fitting the exhaust union nut

€11.50*
Holder for pole wheel and gear wheel
Special tool - makes installation on the engine easier!

€22.80*
Woodruff key (wedge) - to the pinion
Matching Woodruff key (pinion gear shaft)

€0.80*
Skip product gallery

Customers also viewed

Chain sprocket
suitable from vehicle no. 20694Chain sprockets with 12 teeth are standard for all models. Depending on requirements or use, however, sprockets with 11 teeth (good climbing ability) or 13 teeth (higher top speed) can also be fitted. The 14-tooth sprocket can only be used after modifying or adapting the housing or using a weaker, non-reinforced chain.

From €18.50*
Saddle cover NSU
Replacement saddle cover for original NSU saddle framewith "NSU" logo! made of rubber, as original incl. 4 fastening rivets available in the colours cream, grey or red-brown

From €34.00*
Holder for pole wheel and gear wheel
Special tool - makes installation on the engine easier!

€22.80*