Skip to main content Skip to search Skip to main navigation

Puller for new ignition system

Product information "Puller for new ignition system"

Suitable puller for our new ignition systems

Herstellerinformationen:
Buzzetti S.r.l. Via Ronchetti 11 21040 Oggiona info@buzzetti.com WEEE-Nummer:


0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Skip product gallery

Similar products

Average rating of 5 out of 5 stars

Alternator side cover
Note different versions! for all 2-speed and 3-speed models with brake lever on the left-hand side of the motor: Quickly N, S, L, N23 and S23 or version for engines with brake lever on the right: Quickly S2, S23-2, F23, TT, TT/K

From €42.00*
Bearing bolt for breaker, type 1
Breaker bearing bolts for all "Type 1" breakers

€6.80*
Breaker
Complete circuit breaker - note the different versions! Type 1 Bosch No. 1217013010, centre hole 6 mm, adjustment via eccentric,most common versionType 2 centre hole 8 mm, adjustment via 2 notches Please refer to the illustrations

From €9.50*

Average rating of 5 out of 5 stars

Capacitor
Typ: Schraubausführung
Ignition capacitor different versions (for soldering or screwing) Capacitors are a frequent source of faults due to their age and should always be replaced

€4.80*
Clutch nut / pole wheel set with spring washers
Set of nuts for clutch or pole wheel, consisting of 1X nut and 2X spring washer - galvanised

€1.00*
Connection plate for cable (on motor)
Connection plate for light cable at the output of the ignition system

€5.20*
Feeler gauge
Feeler gaugefor setting the contact breaker and ignition13 sheets0.05 - 1mm

€8.90*
Horn (buzzer) 6 V
6 volt snare, universal with holder - alternating current

€7.90*
Ignition cable 1 m
Ignition cable available in 5 mm or 7 mm diameter.Length per unit: 1 m Manufacturer: 5mm: orig. Bosch7mm: Herth+Buss

From €3.60*
Ignition cable 1.90m roll 5mm
Ignition cable 5mm, especially for ignition coil type 3

Content: 1.9 Meter (€2.05* / 1 Meter)

€3.90*
Ignition coil
Ignition coil suitable for various models, please measure and compare accordingly! Dimensions: Type 1: Overall length 73 mm, hole spacing 53 mm Type 2: Overall length 74 mm, hole spacing 50 mm Type 3: Overall length 77 mm, hole spacing 54 mm Type 4: Replacement is type 1

From €50.00*
Ignition system alternator, new NSU Quickly, black coil
Complete new ignition generator for NSU Quickly -Ready to install without soldering!with black, reinforced ignition coilAdvantages: very strong ignition spark ready mounted with cable (no soldering) Extremely durable Very low susceptibility to faults Quick to replace Ignition coil in original design with wide pole shoes! Each ignition is tested individually on the test bench Light output 17 watts, incl. pole wheel.Suitable for all models.

€169.00*
Skip product gallery

Customers also bought

Puller for pole wheel
Pole wheel puller for all Quickly motors Notes: Please note that the thread of the crankshaft must be protected by a brass pressure piece or similar if the pole wheels are stuck.Alternatively, the nut of the pole wheel can remain on the threaded stub.(loosen nut and turn flush to the end of the thread).

€8.80*
Spark plug "Bosch"
Bosch Multi-range candle, ideal for the Quickly

€4.90*
Ignition system alternator, new Quickly N,S,L ready for installation
New complete ignition system with pole wheel for the Quickly, ready to fit incl. ignition cable and light connection plate,Every ignition system is tested by us. Optimum performance again with new ignition!

€145.00*
Puller for chain sprocket
Enables safe and trouble-free removal of all chain sprockets!

€14.80*
Start carburettor cpl. 1/12/127
New starter carburettor with 12 mm passage!

€89.00*
Ignition system alternator, new NSU Quickly, black coil
Complete new ignition generator for NSU Quickly -Ready to install without soldering!with black, reinforced ignition coilAdvantages: very strong ignition spark ready mounted with cable (no soldering) Extremely durable Very low susceptibility to faults Quick to replace Ignition coil in original design with wide pole shoes! Each ignition is tested individually on the test bench Light output 17 watts, incl. pole wheel.Suitable for all models.

€169.00*
Skip product gallery

Customers also viewed

Puller for pole wheel
Pole wheel puller for all Quickly motors Notes: Please note that the thread of the crankshaft must be protected by a brass pressure piece or similar if the pole wheels are stuck.Alternatively, the nut of the pole wheel can remain on the threaded stub.(loosen nut and turn flush to the end of the thread).

€8.80*
Holder for pole wheel and gear wheel
Special tool - makes installation on the engine easier!

€22.80*
Clutch nut / pole wheel set with spring washers
Set of nuts for clutch or pole wheel, consisting of 1X nut and 2X spring washer - galvanised

€1.00*
New
Handle covers grey, PVC for gas and gearstick
suitable for Quickly 23 models

€8.50*
Drive chain double reinforced
Original Wippermann Chain, double reinforced in various lengths incl. lock (no. 18) suitable for Quickly S23-2,F When using a 13 chain sprocket, you need the chain with 114 links When using a 14 chain sprocket, you need the chain with 116 links

From €19.80*