The repair instructions were once aimed at the mechanics in the NSU workshops and conveyed the specialist knowledge required for a successful repair. Today, on the other hand, the content is primarily aimed at NSU Quickly enthusiasts. Old knowledge from the 1960s is required to successfully maintain the NSU Quickly, to carefully preserve its value or to continue using this popular historic moped. New edition! Old knowledge 1962-

Special nut for the bearing bolt on the suspension fork/swing arm

Stainless steel nut with galvanised spring washer for fastening the brake lever to the brake key (wheel hub)

6-piece, VA

8-piece fastening set nuts and washers for the cylinder head- optionally galvanised or stainless steel -

Stainless steel oil filler or drain plug

Oil drain plug + oil filler plug + oil check plug + 3 seals

with 6mm hose connection. The petrol filter can be dismantled and cleaned, Made in Italy. Dimensions: - Outer diameter approx. 22mm - Total length approx. 64mm - Filter length approx. 40mm - Length of the connections approx. 12mm

New, original front wheel hub for Quickly S2, 2-23,T,TT,TT-K

suitable for S23, S2-23, F23, TT, TT/K

for upper mounting of the Quickly, T,TT,F, S2-23, S23 headlight insert (image no. 10)

Collar screw for fastening the decorative lever no. 164400909, galvanised

Oval-head screw for fastening the throttle grip - galvanised - suitable for all models except L and T

for gear lever mounting, suitable for all models except L + T

Inexpensive pillion footrests, folding

Original "Union" pedals (without reflector for right and left - especially fitted to the Quickly 23 models)

Fabric petrol hose length 1 metre

Petrol hose, clear - new quality! - Petrol and oil resistantUnit 1 m

Classic design - Tap body made entirely of metal suitable for all models (except Quickly T), incl. sealespecially for Quickly N, with small tank (extra long strainer)

Seal between petrol tap and tank

Piston pin suitable for all models / Quickly engines.

Standard fuse for original pistons, replace after each change!

Piston pin lock e.g. for Meteor or Parmakit pistons

different versions,please select accordingly!

Gearwheel for press-fitting on large gearwheel, 13 teethJaw width 11.3mmsuitable for Quickly S23-2,F - 3-speed motor, brake right

Set: 1L HS-Premium filler (light grey) "Spiess-Hecker" + 250 ml hardener (included!)Mixing ratio: 4:1

Rust protection primer/adhesive primer

(from frame to headlight) 1 unit = 50 cm

for all starter carburettor versions

Beautiful metal emblem for toolbox cover and handlebar fairing Quickly 23

Radial seal ring shift shaft for 3-speed engines

Oil seal for the left crankshaft sideis recommended for an engine overhaul!

Crank drive right

Sealing ring for chain sprocket motor housing

Rubber pad for the rear light of the 23 models - N23,S23,S23-2,F23

1-litre tin of 2K acrylic thinner

for headlight adjustment on Quickly L and all 23" models (except N23)

Replacement chrome ring, top quality for Quickly speedometers, eye-catcher for every moped

For attaching the jet needle, suitable for all carburettors

Rim tape from Heidenaushould be replaced every time you change your tyres.

1 set of rocker arms for Quickly F23 and S2-23, newly galvanised and stored - only in exchange!Please send your cleaned and exchangeable old parts in advance.

Original rocker arm for Quickly F23 or S2-23 , left or right

Front support for tank S23,S23-2,F23

Rubber cap for ignition cable-ignition coil connection with screwed connection (black plastic coils)

on the frame for all vehicles with starter carburettor

Rubber grommet on the carburettor (adjusting screw) at the top

Rubber grommet for brake cable and speedometer cable for Quickly S23, S2-23 and F23 on the front mudguard

1 pair of rubber plugs for damping the suspension - are inserted into the springs.

1 set of rubber stops for steering / suspension fork

Rubber seal, cream white for installation between speedometer and headlight

Screw nipple for attaching the decorative cable to the lever on Quickly N,S,N23,S23,F

Screw plug, aluminium at the bottom of the carburettor

Set with 2 bolts VA, incl. spring washers + nut for mounting clamp exhaust silencer

8-piece, made of VA, suitable for F23,S2-23, S23

Special mounting kit for the Quickly 23 handlebar fairing.5-piece and with stainless steel screws

Fastening screw set for the tool box of the 23 models in stainless steel suitable for S23, S2-23, F23 -as original-

20 special screws + nuts and spring washers for fastening the decorative moulding

Fastening screw set for carburettor