Used Pillion seat for Quickly T, condition as per picture for restoration

Piston pin suitable for all models / Quickly engines.

Standard fuse for original pistons, replace after each change!

Piston pin lock e.g. for Meteor or Parmakit pistons

different versions,please select accordingly!

Bushing set for the rear hub - Quickly TTK carrier plateAlso for Quickly T and TT, last versions with TTK hub

Gearwheel for press-fitting on large gearwheel, 13 teethJaw width 11.3mmsuitable for Quickly S23-2,F - 3-speed motor, brake right

Set: 1L HS-Premium filler (light grey) "Spiess-Hecker" + 250 ml hardener (included!)Mixing ratio: 4:1

Rust protection primer/adhesive primer

2 pieces of profile rubber, ivory-coloured for mounting on Quickly L or T handlebars

(from frame to headlight) 1 unit = 50 cm

Light switch for Quickly T and TT, also suitable for TT-K (without short-circuit circuit)

Used 3-speed engine for Quickly T, for restoration.Incl. blower cooling and main stand.The engine was still running before removal.However, an overhaul is recommended

Used seat cushion for Quickly T - condition as pictured

Replacement for original, provides significantly more power due to more air flow - better filter effect

complete with sliding blocks

Radial seal ring shift shaft for 3-speed engines

Oil seal for the left crankshaft sideis recommended for an engine overhaul!

Crank drive right

Sealing ring for chain sprocket motor housing

New cover sleeve for rear shock absorbers suitable for Quickly F, T, TT, TT/K and Quick 50

1 set of struts/shock absorbers for rear wheel, second-hand

Pränafa Ausf.

Rear wheel with aluminium rim, used for Quickly T or TT (without brake plate)

1-litre tin of 2K acrylic thinner

for headlight adjustment on Quickly L and all 23" models (except N23)

For attaching the jet needle, suitable for all carburettors

Rim tape from Heidenaushould be replaced every time you change your tyres.

Rocker arm set for Quickly T, TT and TT-K used and reconditioned in exchangeThe rocker arms are newly galvanised, fitted with new bushes and ready for installation. Please send in your cleaned and exchangeable old parts in advance.

Rubber grommet on the carburettor (adjusting screw) at the top

Screw plug, aluminium at the bottom of the carburettor

Complete set with screws, nuts, washers, spring washers for fastening the Quickly T stainless steel air duct

Set with 2 bolts VA, incl. spring washers + nut for mounting clamp exhaust silencer

20 special screws + nuts and spring washers for fastening the decorative moulding

Fastening screw set for carburettor

2 seals, self-adhesive, for the Bakelite piece

Seal for the 3-speed shift cable on the engine (lower bushing)

O-ring on the clutch cup

Special sealing ring for bottom bracket axle for all models

O-ring between clutch basket and crankshaft - Important! lack of compression if sealing ring is missing

Lock washers for shock absorber bolts (1 piece required per shock absorber)

Set with 3 sealing rings: 1x each for oil filler/drain plug and oil check plug

Set of 2 bearing bushes for one rocker arm, suitable for all models from F.No. 482755 (except Cav)

Set with bearing bush, bearing bolt and fusesuitable for front or rear shock absorbersOne set is for one shock absorber!

suitable for all models from F.No. 482755 (except Cav.) , set of 2 pieces for one rocker arm

Nut + spring washer for chain sprocket galvanised

Set of 2 nuts + 2 spring washers

Set of special nuts for shock absorbers

Suitable for tilt stands N23,S23,S2-23,F,T,TT, TT/K Set consists of 2 bearing collar bolts + 2 nuts + 4 spring washers

Set with 2 clamping screws + 2 spring washers

Clutch repair kit:Sealing rings for clutch cup and crankshaft,Circlip for clutch basket and lock washers for clutch shaft - 5-piece - Set price -

Suitable for all models from F.No. 482755 (except Cav.)Set of 2 for one rocker arm

Screw set for fastening the base plate and the breaker. 9-piece

+ 2 front cover sleeves, incl. nuts, stop ring and lock

Set for left + right, suitable for Quickly T up to F.No. 2928721!

2 nipples for attaching the 3-speed gearshift cable to the engine (gearshift paddle)