Clutch cable for various models and versions with or without adjusting screw, depending on the variant!

Clutch cup, new!

Clutch facing plate for all engines, from current production - no old stock in storage

Steel disc1 steel disc is required for a 3-disc clutch, 2 for a 5-disc clutch

Clutch set for 3 or 5 disc clutch from current production. No hardened old stock!

Clutch lever for 3-speed models (Quickly N,S, S23,S2, S2-23, F23)

Clutch lever, galvanised - the clutch cable is usually too long when using old, bent levers!

for locking the clutch lever -Enables "bicycle operation

Set of nuts for clutch or pole wheel, consisting of 1X nut and 2X spring washer - galvanised

Clutch shaft on engine, galvanised

Clutch spring, suitable for all engines, replace the spring when replacing the linings!

Connecting rod bushing for original crankshaftBushing must be reamed to piston pin dimensions .

Improved version with wider bars - for all 3-speed engines! When replacing the old version with short centre webs (see illustration), the sprocket on the countershaftmust also be replaced.

Cover for shift cable on engine (drive disc) 3-speed -

Rubber cover cap for chain case

Cover gasket for cover plate for starter carburettor

complete:incl. pressure pin, clamping spring, set screw, 2x screw for cover plate + sealCover plate + seal

Crank keys for bottom bracket axle or pedal crank - 1 set of 2 including nuts

Crankcase centre section for all 2- or 3-speed engines for 2-speed only used, for 3-speed also available as new part, please select accordingly on the scroll bar

Special crankshaft for the discerning rider, manufactured using the latest technology. Very stable, durable design with connecting rod needle bearing!

Full cheek crankshaft type "Sport"More power and torque with the full cheek crankshaft.Achieve optimum performance in the mid to upper speed range thanks to greater pre-compression.Very stable crankshaft with needle bearings - Suitable for all engines! More torque Better pre-compression Better filling ratio Needle bearing mounted stable up to highest speeds

for Quickly TT and TTK on the tank and frame

Beautiful emblem - as original -suitable for front and rear mudguards (2 pieces required) -without mounting parts-

4-piece special mounting kit for coat of arms shield

Cylinder head in the original 1.7 hp version for significantly more power - fits all Quickly engines. Fully assembled with new valve and deco gasket, ready to fit!

Cylinder-head gasket 0.75, reinforced, Made in Germany

Used cylinder head for Quickly T with fan cooling, as shown

New decorative lever in original design

Light and horn switch - only for export version Switch for mounting on handlebars Switch position 1-0-2 and horn button

Special disc, required for the valves of the 1st version (from engine number 522990)

Assembly lever, required for various work on the engine (levering off the clutch cup, clutch basket etc.) Set with 2 levers

Model Which model? Chain length 108 links, reinforced Quickly Cavallino Chain length 112 links, reinforced Quickly N, S, L, T, TT u. TT-K (with standard sprocket 12 Z) Chain length 114 links, reinforced or double reinforced Quickly S2-23, F23 and all previously listed models when converting to a 13 sprocket Chain length 116 links double reinforced Quickly S2-23 and F23 when using a 14 sprocket Brand chain Wippermann incl. lock (no. 17) When using a 13 chain sprocket, you need the chain with 114 links

Driver disc for all 3-speed engines

Brake driver for Quickly S2, F, T and TT (versions with brake lever on the right of the motor)

Sealing rings, set of 4 for brake driver (2x inside and 2x outside)

Exhaust cover for Quickly TT and TT-K, high-gloss chrome-plated

Replacement flute for the silencer 167102505

Suitable for all models from F.No. 305018 -chrome-plated

Exhaust silencer, suitable for all Quickly models, chrome-plated -incl. exhaust flute-

Set: exhaust silencer, clamp + screw, manifold right, clamp, union nut, manifold gasket

Exhaust fitting: Cylinder manifold

1 set of aluminium notched nails for fixing the type plate

Complete float with needle suitable for all Quickly types.

Float housing cover for all starter carburettor versions

For sealing the float housing - suitable for all carburettor designs

Cover over top steering cone, galvanised

Frame, used - as illustrated

Cover sleeve for front shock absorber suitable for Quickly T,TT TT/K and Quick 50

Set with 2 pieces

Gebrauchtes Vorderrad für Quickly S2-23, T, TT, incl. Bremsplatte

Replacement seal for all models

Aluminium, high gloss incl. rubber seal

Throttle slide for starter carburettor versions, suitable for 1/9/22 and as a replacement for 1/12/127 carburettors

Special disc in the throttle slide - is placed over the retaining plate