Clamp between exhaust manifold and silencer suitable for all models, chrome-plated

Clamp complete with bolts and nuts for attaching the saddle to the seat post (seat tube)

suitable for Quickly N,S,L, N23,S2

Fastening screw with cone for attaching the saddle to the frame

Clamping spring for cover plate pressure pin

Retaining clips for the profile rubber on the frame of the Quickly L Set of 2 made of stainless steel

Classic petrol tap in metal design (including strainer), suitable for all models except Quickly T. For Quickly N with small tank, please select Classic petrol tap.

Original clutch basket, inner for 5-plate clutch

New outer clutch basket for 5-plate clutch

inner clutch basket for 3-way clutch, new

Clutch cable for various models and versions with or without adjusting screw, depending on the variant!

Clutch cup, new!

Clutch facing plate for all engines, from current production - no old stock in storage

Steel disc1 steel disc is required for a 3-disc clutch, 2 for a 5-disc clutch

Clutch set for 3 or 5 disc clutch from current production. No hardened old stock!

Clutch lever for 3-speed models (Quickly N,S, S23,S2, S2-23, F23)

original clutch lever Magura for Quickly L and T

New clutch lever for Quickly 2-speed, polished aluminium

Clutch lever, galvanised - the clutch cable is usually too long when using old, bent levers!

for locking the clutch lever -Enables "bicycle operation

Set of nuts for clutch or pole wheel, consisting of 1X nut and 2X spring washer - galvanised

Clutch shaft on engine, galvanised

Clutch spring, suitable for all engines, replace the spring when replacing the linings!

Set with screw, mounting nut, clamping bolt and bottom bearing bolt! Suitable for Quickly N,S,L,N23 with 4.5 litre tank!

Connecting rod bushing for original crankshaftBushing must be reamed to piston pin dimensions .

Connection plate for light cable at the output of the ignition system

High-quality 2-component paint colour "coral red" for Quickly L with the colour combination walgrey/coral red (mudguards, tankPaint is mixed with hardener in a ratio of 2:1 (hardener must be ordered separately)

Improved version with wider bars - for all 3-speed engines! When replacing the old version with short centre webs (see illustration), the sprocket on the countershaftmust also be replaced.

Countershaft with collar, suitable for all 2-speed engines.

Cover for shift cable on engine (drive disc) 3-speed -

Cover gasket for cover plate for starter carburettor

Chrome-plated cover nut on the suspension fork

New cover plate for rear hub Quickly N, S and L - bright galvanised

complete:incl. pressure pin, clamping spring, set screw, 2x screw for cover plate + sealCover plate + seal

Cover plate between engine and frame, suitable for all models

Cover screw fitting for Bing carburettor incl. adjusting screw

Crank keys for bottom bracket axle or pedal crank - 1 set of 2 including nuts

Crankcase centre section for all 2- or 3-speed engines for 2-speed only used, for 3-speed also available as new part, please select accordingly on the scroll bar

Special crankshaft for the discerning rider, manufactured using the latest technology. Very stable, durable design with connecting rod needle bearing!

Full cheek crankshaft type "Sport"More power and torque with the full cheek crankshaft.Achieve optimum performance in the mid to upper speed range thanks to greater pre-compression.Very stable crankshaft with needle bearings - Suitable for all engines! More torque Better pre-compression Better filling ratio Needle bearing mounted stable up to highest speeds

Cylinder head in the original 1.7 hp version for significantly more power - fits all Quickly engines. Fully assembled with new valve and deco gasket, ready to fit!

Cylinder-head gasket 0.75, reinforced, Made in Germany

Set of 16 rollers

New moulding on the frame (access) Quickly L

Vierteiliger Dichtungssatz für den Quickly-Motor. Bestehend aus Zylinderkopf-, Zylinderfußdichtung, Kurbelgehäuse und Kupplungsdeckeldichtung. 

Light and horn switch - only for export version Switch for mounting on handlebars Switch position 1-0-2 and horn button

Special disc, required for the valves of the 1st version (from engine number 522990)

Special disc for the shift shaft on the 2-speed engine

Stainless steel disc suspension fork

Assembly lever, required for various work on the engine (levering off the clutch cup, clutch basket etc.) Set with 2 levers

Rust-free and durable: Made of high-quality stainless steel, distance roller to the quick-release axle