for rear frame Quickly L (for 1 vehicle)

2 pieces of profile rubber, ivory-coloured for mounting on Quickly L or T handlebars

(from frame to headlight) 1 unit = 50 cm

Protective conduit for routing the cable pulls and cables in the frame.

for all starter carburettor versions

Complete rear light for Quickly L, with rubber base, ready to fit (without bulb)

Special rear light underlay for Quickly L with centre fold

New retaining pin for attaching the Quickly L spring - now stainless steel!

Beautiful metal emblem for toolbox cover and handlebar fairing Quickly 23

Quickly" lettering on the right and left for Quickly L rear panelling - chrome-plated, high-quality finish

Radial seal ring shift shaft for 3-speed engines

Oil seal for the left crankshaft sideis recommended for an engine overhaul!

Crank drive right

Made from high-quality material, this sealing ring ensures that your wheel bearing is protected from moisture and dirt

up to motor no. 21025 (repair version only)

Sealing ring for chain sprocket motor housing

for various models

1-litre tin of 2K acrylic thinner

Tilting reflector for Quickly "L" headlights

for headlight adjustment on Quickly L and all 23" models (except N23)

Consisting of:Float housing cover with swab, screws, sealing ring, float

Replacement chrome ring, top quality for Quickly speedometers, eye-catcher for every moped

Replacement mirror for the original Quickly L mirror mount

For attaching the jet needle, suitable for all carburettors

Rim tape 26", should be replaced with every tyre change

Rocker arm set for Quickly N, S,L, S23,N23 used and reconditioned in exchangeThe rocker arms are newly galvanised, fitted with new bushes and ready for installation.Please send us your cleaned and exchangeable old parts in advance.

Replacement rubber for all side stands

Rubber cap for ignition cable-ignition coil connection with screwed connection (black plastic coils)

on the frame for all vehicles with starter carburettor

Rubber grommet on the carburettor (adjusting screw) at the top

Rubber grommet at the bottom of the frame exit to feed through the cables

Grommet between saddle and frame - only for Quickly L - , beige

f. Bowden cable guide handbrake cable and speedometer cable Quickly S or L (2 pieces are required per vehicle) also handlebar fairing TT/TTK u.Rear light cable / mudguard grommet TT

Suitable for Quickly N,S,L,N23,S2 for 3.1 and 4.5 l tanksColour: silver-grey

1 pair of rubber plugs for damping the suspension - are inserted into the springs.

1 set of rubber stops for steering / suspension fork

Rubber seal, cream white for installation between speedometer and headlight

New saddle shaft tube, galvanised

Stainless steel screw for tank - versions for small and large tanks

Screw plug, aluminium at the bottom of the carburettor

Complete set with screws, nuts, washers, spring washers for fastening the Quickly T stainless steel air duct

Screw set for fastening the rear fairing / frame rear Quickly L - screws, nuts, washers - completely made of stainless steel

Special screw + nut galvanised

Fastening screw set for carburettor

Seal for the 3-speed shift cable on the engine (lower bushing)

O-ring on the clutch cup

Special sealing ring for 2-speed selector shaft

Special sealing ring for bottom bracket axle for all models

O-ring between clutch basket and crankshaft - Important! lack of compression if sealing ring is missing

Set with 3 sealing rings: 1x each for oil filler/drain plug and oil check plug

Set of 2 bearing bushes for one rocker arm, suitable for all models from F.No. 482755 (except Cav)

Set of 2 for one vehicle, for mounting the wire stand

suitable for all models from F.No. 482755 (except Cav.) , set of 2 pieces for one rocker arm