Nut + spring washer for chain sprocket galvanised

Set of 2 nuts + 2 spring washers

old version up to vehicle no. 447150, galvanised

5-piece bearing set with our quality bearings "!house brand"

Set with 2 bearing bolts (special bolt) + 2 stop nuts for rocker arm bearing

Set of 2 pieces 4 pieces are required per vehicle.

Set with 2 clamping screws + 2 spring washers

Clutch repair kit:Sealing rings for clutch cup and crankshaft,Circlip for clutch basket and lock washers for clutch shaft - 5-piece - Set price -

Suitable for all models from F.No. 482755 (except Cav.)Set of 2 for one rocker arm

Set with 2 bolts + 4 spring washers (VA)

Screw set for fastening the base plate and the breaker. 9-piece

Repair kit for carburettor (float bowl cover, sealing ring and both screws)

Set of grip covers for Quickly L: 1x for shift side and 1x for throttle side

2 nipples for attaching the 3-speed gearshift cable to the engine (gearshift paddle)

Set of retaining clips for fixing the reflector (4 parts)

Set of 3 with 0.2 + 0.3 + 0.5 mmbetween bearing cone and brake plate

Bolt set for handlebar support, stainless steel - consisting of 2 bolts, 2 nuts and lock washers.

Set of 2 screws, complete with lock washers and nut, stainless steel

Set of 3 piecesThickness 0.5 -0.6 and 0.7

Set of 2 shock absorber rubbers for Quickly L

one pair of rubber blocks under the tank - for Quickly N, S, L, N23, S2 - black -Suitable for all 3.1 and 4.5 litre tanks.

Set with seal, cap and locking disc for decompression valve --set price

Set of 2 springs, suitable for Quickly N,S,L,N23,S23,S23-2,F also for Quickly L suspension

One set of bump stops with rubber buffer (2 pieces for one vehicle), suitable for N,S,L,N23,S23,S2-23,F23

Shift fork for all 2-speed engines

Used shift fork for 3-speed gearbox

Shift shaft for all 2-speed engines

Shift spring in gearbox, for all 2-speed engines

Shift claw for all 2-speed engines Installation note: the unscrewed side must face the ignition!

for headlights and fittings 2-coat paint - must be painted over with clear coat.

Suitable for all carburettor models

Air slide cover on frame for all versions without starter carburettor, galvanised

Sliding block, slider for internal throttle grip on Quickly L and T

New sliding wheel for the improved countershaft

Set with cover seal, float seal ring, seal for needle nozzle, clamping spring, retaining plate for nozzle needle, disc for throttle slide, 2 screws each for float housing cover and cover plate Set price

between gear shaft and gear wheel

Set with 0.2 + 0.3 + 0.5 mm disc

Spacer tube on bottom bracket axle for 2-speed motorInstallation note: Clearance between spacer tube and large gear wheel must be 0.2-0.3 mm!

Spacer tube on the bottom bracket axle 3-speed motors (left)

Spacer tube to bottom bracket axle 3-G. for all "left" brake motors (not Quickly T,TT,F) 31.2 mm long

Spacer tube, 39 mm for screwing on the bearing cones

Bosch Multi-range candle, ideal for the Quickly

Plug connector as original! With "NSU" logo

Spark plug connector, orig. Beru, water-protected and interference-suppressed

incl. rubber seal suitable for: Quickly N,S,L,N23,S23,S23-2,S2,F - not for T,TT,TT/K

silver-grey - Length: 850 mm Connection nuts top and bottom identical

New speedometer drive with hub engagement, stable design in top quality, like original VDO

Now new!Set of 18 inner and outer spokes and 36 nipples suitable for Quickly L (26", full hub) for 1 wheel Spoke length: 233 mm, outer nipple diameter approx. 5.4 mm Original "cloverleaf" spoke Berg-Union, leading manufacturer and supplier for two-wheelers of the 50s and 60s --Chrome-plated thick spokes on request also available with "smaller" nipples, i.e. outer diameter of the nipple shaft approx. 4.9 mm (e.g. when using the original rims)

Galvanised spring retainer on the clutch

Sprocket, chain wheel NSU Quickly 2nd version (bolted), 36 teeth

New starter carburettor with 12 mm passage!

Start slide for all start carburettors

Steering lock, as original incl. 2 keys

Suitable for top or bottom (order 2 pcs.)

Stud bolts for cylinder mounting, galvanised - 4 pieces 7 required per engine