Rust protection primer/adhesive primer

(from frame to headlight) 1 unit = 50 cm

for all starter carburettor versions

Headlight insert, ready to install for Quickly N, S, N23 with 17 W. system (reflector, gasket, chrome ring, glass, clamps) ready mounted !

Beautiful metal emblem for toolbox cover and handlebar fairing Quickly 23

Radial seal ring shift shaft for 3-speed engines

Oil seal for the left crankshaft sideis recommended for an engine overhaul!

Crank drive right

Made from high-quality material, this sealing ring ensures that your wheel bearing is protected from moisture and dirt

Sealing ring for chain sprocket motor housing

matt chrome-plated

Rubber pad for the rear light of the 23 models - N23,S23,S23-2,F23

NEW! - finally available! newly manufactured rear wheel hubs for the Quickly N, S and N23. greatly improved braking performance standardised bearings (no cumbersome, expensive and wear-prone cone bearings) High-quality material - broken hubs are a thing of the past! Improved durability of the spokes due to material reinforcement in the suspension area excellent smooth running due to grooved ball bearings Manufactured entirely from solid material Made in Germany all previous parts (brakes, chain wheel etc. can be used in the same way nickel-plated surface Scope of delivery: Hub with bearing, mounting piece right and left made of stainless steel (without thru axle) We recommend ordering the shim set 165100054S to compensate for tolerances of the original hub if required. to be able to equalise brake plates

1-litre tin of 2K acrylic thinner

Reflector for Quickly N,S,N23,S2 models Note different versions - 3 watt or 17 watt(3 watt version only up to model year 1955)

Replacement chrome ring, top quality for Quickly speedometers, eye-catcher for every moped

Fastening clips for reflector/chrome ring 2 pieces + retaining spring are required for 15 W headlights. For 3 W lamp 4 pieces

For attaching the jet needle, suitable for all carburettors

Retaining spring for fixing reflector and bulb in 17 W systems

for Quickly N23for painting - unpunched - 36 holes, hole diameter: 6 mm

Rim tape from Heidenaushould be replaced every time you change your tyres.

Rocker arm set for Quickly N, S,L, S23,N23 used and reconditioned in exchangeThe rocker arms are newly galvanised, fitted with new bushes and ready for installation.Please send us your cleaned and exchangeable old parts in advance.

Replacement rubber for all side stands

Rubber cap for ignition cable-ignition coil connection with screwed connection (black plastic coils)

on the frame for all vehicles with starter carburettor

Rubber grommet on the carburettor (adjusting screw) at the top

Suitable for Quickly N,S,L,N23,S2 for 3.1 and 4.5 l tanksColour: silver-grey

1 pair of rubber plugs for damping the suspension - are inserted into the springs.

1 set of rubber stops for steering / suspension fork

Rubber seal, cream white for installation between speedometer and headlight

New saddle shaft tube, galvanised

10-piece set of springs for the NSU saddle

Stainless steel screw for tank - versions for small and large tanks

Screw nipple for attaching the decorative cable to the lever on Quickly N,S,N23,S23,F

Screw plug, aluminium at the bottom of the carburettor

Complete set with screws, nuts, washers, spring washers for fastening the Quickly T stainless steel air duct

Set with 2 bolts VA, incl. spring washers + nut for mounting clamp exhaust silencer

Special screw + nut galvanised

Fastening screw set for carburettor

2 seals, self-adhesive, for the Bakelite piece

Seal for the 3-speed shift cable on the engine (lower bushing)

O-ring on the clutch cup

Special sealing ring for 2-speed selector shaft

Special sealing ring for bottom bracket axle for all models

O-ring between clutch basket and crankshaft - Important! lack of compression if sealing ring is missing

Set with 3 sealing rings: 1x each for oil filler/drain plug and oil check plug

Set of 2 bearing bushes for one rocker arm, suitable for all models from F.No. 482755 (except Cav)

suitable for all models from F.No. 482755 (except Cav.) , set of 2 pieces for one rocker arm

Nut + spring washer for chain sprocket galvanised

Set of 2 nuts + 2 spring washers

5-piece bearing set with our quality bearings "!house brand"

Set with 2 bearing bolts (special bolt) + 2 stop nuts for rocker arm bearing

Suitable for tilt stands N23,S23,S2-23,F,T,TT, TT/K Set consists of 2 bearing collar bolts + 2 nuts + 4 spring washers