2K system, 400 ml spray can

Shift wheel on the engine for all 2-speed versions

Complete overhaul kit for the 3-speed Quickly engineConsisting of all bearings, brand make FAGall shaft seals, all O-rings + manifold sealing ring

Starting carburettor adjusting screw for throttle cable adjustment incl. nut

Air filter in frame for all models without starter carburettor

Inner air filter basket (rotatable) for versions with starting device on the frame

Air filter in frame for all models with starter carburettor

Set with air filter fastening screw, stop nut and retaining star

Special tool for easy assembly of the inner clutch basket

Ball bearing NSU-Quickly Motor quality from FAG

Ball bearing for crankshaft (quality from FAG) 2 pieces are needed!

Ball bearing for the gear shaft 2-speed engine (2 pieces are required)for 3-speed engines one bearing is required and one bearing Article No. 160100601

f. Driven shaft 3-G.

5-piece ball bearing set - brand bearings FAG

5-piece ball bearing set with brand bearings from FAG Complete set of bearings for engine overhaul

Complete ball set for steering, 42 balls (for top bottom)

Breaker bearing bolts for all "Type 1" breakers

2nd version - brake drum or opposite side

Bearing screw - special screw for rocker arm bearings

Bearing shell for the wheel ball bearings of the NSU Quickly

Bearing spacer bush for rocker arm (2 required per vehicle)

galvanised, incl. washer and split pin

Dummy cover for headlights (required if no speedometer is used)

Bearing bolt for driving disc on 3-speed engine

Bottom bracket axle for all 2-speed motors and 3-speed motors with left brake

the Bowden cable set contains: 1 x throttle cable, decompression cable, handbrake cable, 2-speed gearshift cable, clutch cable

1 x each decompression cable, throttle cable, handbrake cable, clutch cable, 2-speed gearshift cable

1 x each decompression cable, throttle cable, handbrake cable, clutch cable, 3-speed gearshift cable

Retaining spring for fastening the speedometer(169204501)in the headlight

Screw at the bottom of the throttle grip - note dimensions! versions possible!

from. F.No. 482755

Note different versions!

Brake lever on the rear wheel hub 2nd version

Set of 2 for all 2 and 3-speed engines with left brake

Length 557 mm Stainless steel brake linkage, incl. locking plate suitable for Quickly N up to frame no. 50340 and N,S,N23,S23 from frame no. 482755 also suitable for Quickly T with Pränafa hub -- Brake linkage bracket is not required --

Without baking

Inner spring for brake shoes 2nd version

Brake return spring on the rear brake, 2nd version - suitable for N,S,L,N23,S23

Completely bonded brake shoes from current production - no cured old stock ( set for one wheel)

(e.g. screws)

6V 15W suitable for 17 Watt systems see also designation on the pole wheel (Example: ELZJ 17 L = 17 watts)Total output 17 watts : 15 W for headlights, 2 W for tail lights)

for all 3-speed engines from no. 743607

Bushing for countershaft 3-speed, left (all engines) also for right crankcase half up to engine 743606

Bearing bush for gearwheel 2-speed motor

Bearing bush (housing/shift shaft) 2 speed

for all 3-speed Quickly engines

Rubber cable strap, as original - for fastening the cable pulls and cables coming out of the frame.Set of 2 pieces

Cap for holding the decorative seal

Adjusting screw for idle throttle - Carburettor without starting device

Carburettor flange gasket approx. 8 mm thick

Original carrying handle, Aluminium polished

1 pair of chain tensioners for Quickly, bright zinc-plated with barrel nuts

Chrome rim for Quickly N, S and L 26X2.00

Very nice chrome ring in 1A chrome quality!

Special fuse under the clutch cup

Clamp between exhaust manifold and silencer suitable for all models, chrome-plated