Classic design - Tap body made entirely of metal suitable for all models (except Quickly T), incl. sealespecially for Quickly N, with small tank (extra long strainer)

Seal between petrol tap and tank

Piston pin suitable for all models / Quickly engines.

Standard fuse for original pistons, replace after each change!

Piston pin lock e.g. for Meteor or Parmakit pistons

different versions,please select accordingly!

Gearwheel for press-fitting on large gearwheel, 13 teethJaw width 11.3mmsuitable for Quickly S23-2,F - 3-speed motor, brake right

Set: 1L HS-Premium filler (light grey) "Spiess-Hecker" + 250 ml hardener (included!)Mixing ratio: 4:1

Rust protection primer/adhesive primer

(from frame to headlight) 1 unit = 50 cm

for all starter carburettor versions

Headlight insert, ready to install for Quickly N, S, N23 with 17 W. system (reflector, gasket, chrome ring, glass, clamps) ready mounted !

Beautiful metal emblem for toolbox cover and handlebar fairing Quickly 23

Radial seal ring shift shaft for 3-speed engines

Oil seal for the left crankshaft sideis recommended for an engine overhaul!

Crank drive right

Sealing ring for chain sprocket motor housing

1-litre tin of 2K acrylic thinner

Reflector for Quickly N,S,N23,S2 models Note different versions - 3 watt or 17 watt(3 watt version only up to model year 1955)

Replacement chrome ring, top quality for Quickly speedometers, eye-catcher for every moped

Fastening clips for reflector/chrome ring 2 pieces + retaining spring are required for 15 W headlights. For 3 W lamp 4 pieces

For attaching the jet needle, suitable for all carburettors

Rim tape 26", should be replaced with every tyre change

Rubber cap for ignition cable-ignition coil connection with screwed connection (black plastic coils)

on the frame for all vehicles with starter carburettor

Rubber grommet on the carburettor (adjusting screw) at the top

Rubber grommet at the bottom of the frame exit to feed through the cables

f. Bowden cable guide handbrake cable and speedometer cable Quickly S or L (2 pieces are required per vehicle) also handlebar fairing TT/TTK u.Rear light cable / mudguard grommet TT

Suitable for Quickly N,S,L,N23,S2 for 3.1 and 4.5 l tanksColour: silver-grey

1 pair of rubber plugs for damping the suspension - are inserted into the springs.

1 set of rubber stops for steering / suspension fork

Rubber seal, cream white for installation between speedometer and headlight

New saddle shaft tube, galvanised

Screw nipple for attaching the decorative cable to the lever on Quickly N,S,N23,S23,F

Screw plug, aluminium at the bottom of the carburettor

Set with 2 bolts VA, incl. spring washers + nut for mounting clamp exhaust silencer

20 special screws + nuts and spring washers for fastening the decorative moulding

Fastening screw set for carburettor

2 seals, self-adhesive, for the Bakelite piece

Seal for the 3-speed shift cable on the engine (lower bushing)

O-ring on the clutch cup

Special sealing ring for bottom bracket axle for all models

O-ring between clutch basket and crankshaft - Important! lack of compression if sealing ring is missing

New seat bench cover for Quickly 23 - cream / blue, custom-fit quality - handmade in Germany

Lock washers for shock absorber bolts (1 piece required per shock absorber)

Set with 3 sealing rings: 1x each for oil filler/drain plug and oil check plug

Set of 2 bearing bushes for one rocker arm, suitable for all models from F.No. 482755 (except Cav)

suitable for all models from F.No. 482755 (except Cav.) , set of 2 pieces for one rocker arm

Nut + spring washer for chain sprocket galvanised

Set of 2 nuts + 2 spring washers

Set with 2 bearing bolts (special bolt) + 2 stop nuts for rocker arm bearing

Suitable for tilt stands N23,S23,S2-23,F,T,TT, TT/K Set consists of 2 bearing collar bolts + 2 nuts + 4 spring washers

Set with 2 clamping screws + 2 spring washers

Clutch repair kit:Sealing rings for clutch cup and crankshaft,Circlip for clutch basket and lock washers for clutch shaft - 5-piece - Set price -

Suitable for all models from F.No. 482755 (except Cav.)Set of 2 for one rocker arm

Set with 2 bolts + 4 spring washers (VA)

Screw set for fastening the base plate and the breaker. 9-piece